tomaszewski wrote:

please help

Use this checksum generator on the flash file, as stated in the tutorial:
https://mega.nz/#!HUMX2RKT!F-FiTFTaSXA_ ... pb0Dgd5BF8

Mino wrote:

https://drive.google.com/file/d/15-1vyRozc6Qq8x5HEB7khcWCnudzEchI/view?usp=sharing
There is more detailed Flashing tutorial.
I hope that this tutorial will help you. Sory for my bad English… if you have a question, ask the admin for help.
Admin please check if the tutorial is right.

Thanks for your contribution! We apreciate

Mino wrote:

https://drive.google.com/file/d/15-1vyRozc6Qq8x5HEB7khcWCnudzEchI/view?usp=sharing
There is more detailed Flashing tutorial.
I hope that this tutorial will help you. Sory for my bad English… if you have a question, ask the admin for help.
Admin please check if the tutorial is right.

Followed these great, detailed instructions, but ran into a problem at the end. Using the SP Multi Port D/L Tool, the scan was "successful (100%)," but, when I clicked "Start All," I received the error "Reminder Bin File is not fully loaded , please check scatter and load setting," and the software would not proceed any further. I looked at the "scatter and load" settings within the software, but there wasn't anything that could be changed. I'm too much of a noob to try to make changes within the actual scatter file (or anywhere else, for that matter) without guidance. Suggestions? Thanks.

(*The red lines in the photos are my doing - blocking personal identifiers.)

Strictly follow the tutorial steps and try it again (also in another PC)

Mino wrote:

https://drive.google.com/file/d/15-1vyRozc6Qq8x5HEB7khcWCnudzEchI/view?usp=sharing
There is more detailed Flashing tutorial.
I hope that this tutorial will help you. Sory for my bad English… if you have a question, ask the admin for help.
Admin please check if the tutorial is right.

Thank you very much!!!! Your flashing tutorial was extremely helpfull!!!

Popcorn

Try to download the ROM again, and also download the checksum generator (maybe the file is corrupted) .... unpack ROM folder and then copy all files from the Checksum generator folder to the ROM folder.
Run checksum.exe and wait for the process to end. then try step 4 again.
That's what it should look like:
https://drive.google.com/file/d/1_ajJC7UeE-M3Z_RqKDcJp2Mmomj6ZXR1/view?usp=sharing
all files have Location...
I hope it will help

kavedel wrote:

Mino wrote:

https://drive.google.com/file/d/15-1vyRozc6Qq8x5HEB7khcWCnudzEchI/view?usp=sharing
There is more detailed Flashing tutorial.
I hope that this tutorial will help you. Sory for my bad English… if you have a question, ask the admin for help.
Admin please check if the tutorial is right.

Thank you very much!!!! Your flashing tutorial was extremely helpfull!!!

I like to help you

Hi there!
I have been continuosly trying to register but was not succeeded and now am able to register. My problem is I want to upgrade my firmware ,currently its BV8000pro-Blackview-V0.1-20170803_20171011-0929 and I want to upgrade it to 20171827 .Rom is already downloaded,Checksum generator shows no error ,Your flashtool shows the com port as well but i want to upgrade it using Sp flashtool. But when i try to flash it through Sp flash tool it show an error :
Status_DA_Hash_mismatch

i tried many time but of no use. Luckily my phone did not brick as i was using latest Sp flash tool i,e v 5.XXX. Now i want to know as your flashtool is showing everything okay ,Can I upgrade using your flashing tool.i am only worried because on many forums i have read that if SP flash tool shows
Status_DA_Hash_mismatch error and you some how manage to flash ,it results in phone Brick.
So could you Guys tell me what should i do? Please keep in mind that Brick Issue.
Thanks

khaqanson wrote:

Hi there!
I have been continuosly trying to register but was not succeeded and now am able to register. My problem is I want to upgrade my firmware ,currently its BV8000pro-Blackview-V0.1-20170803_20171011-0929 and I want to upgrade it to 20171827 .Rom is already downloaded,Checksum generator shows no error ,Your flashtool shows the com port as well but i want to upgrade it using Sp flashtool. But when i try to flash it through Sp flash tool it show an error :
Status_DA_Hash_mismatch

i tried many time but of no use. Luckily my phone did not brick as i was using latest Sp flash tool i,e v 5.XXX. Now i want to know as your flashtool is showing everything okay ,Can I upgrade using your flashing tool.i am only worried because on many forums i have read that if SP flash tool shows
Status_DA_Hash_mismatch error and you some how manage to flash ,it results in phone Brick.
So could you Guys tell me what should i do? Please keep in mind that Brick Issue.
Thanks

Just pay attention and stricly follow our flashing tutorial:
viewtopic.php?f=192&t=319505

Everything will work

Despite of sp flashtool showing Status_DA_HASH_MISMATCH Error???
Please Elaborate as i Asked you to keep that phone brick issue in mind...